#1 As long as you only need access to the router and the modem in bridge mode without disconnecting your computer from the RJ-45 WAN router: a) Make sure that the RJ-45 WAN port router's LAN and the modem combo's LAN are not in the same subnet. I think the end result turned out to be better for me than it was for cr006f, with fewer modifications to the modem settings and no residual issues. After we hung up, I thought I'd try selecting "Yes" on the Internet Setup page for Internet Connection login. #2 Here is an example of what I mean by two subnets. #5 Be strongly advised as long as the RJ-45 router's WAN IP is set to Static and is in the same subnet as the Actiontec GT784WN and this other RJ-45 router is not a Dual WAN port router of any kind (RJ-45 WAN1 and RJ-45 WAN2, RJ-45 WAN and 4G/LTE, RJ-45 WAN and POTS dial-up, ETC..) you (and the computers that are behind this RJ-45 WAN port router) are not going to be able to access the Internet! When I told the Verizon tech what I was trying to do, he offered to walk me through the process. Under "IP Addressing" on the left, I selected "WAN IP Settings." Handy writeup from another forum that I referred to but didn't follow exactly: http://www.dslreports.com/forum/r27205081-modem-router-Putting-a-Actiontec-GT784WNV-into-Bridge-Mode, http://taldar.wordpress.com/2009/07/14/actiontec-airport/, 05-10-2019 While I have no idea of why you would switch from DSL to Cable, you may find this interesting if you were to do that. Forgot to write the version down: http://screenshots.portforward.com/routers/Actiontec/GT784WNV/. #1 Your computer must have a wired NIC. Try searching. #4 Now in the third router, setup it WAN IP to be Static in the same subnet as the GT784WN. It took a minute for the settings to change, and then the Internet light on the GT784WNV went out. Although the solution to my problem was somewhat different than it was for cr006f, I figured there may be other folks in the same boat who also need an alternative solution. Router Ip address. For example with the primary IP Address 192.168.2.1 with the subnet mask of 255.255.255.0, the first DHCP Address that it handles out is 192.168.2.100 and the last DHCP Address that it handles out is 192.168.2.254 - then the other router's LAN IP Address could be 192.168.2.6. c) Disable the DHCP Server in the second RJ-45 WAN port NAT router. 01-26-2020 Can I set it up so that it is NOT connected to DSL but becomes a mini-router that provides WiFi in a … 07:31 AM LawrenceC. For example the RJ-45 router's IP LAN 192.168.1.1 (mask 255.255.255.0) and your modem combo LAN is 192.168.0.1 (mask 255.255.255.0). All in all, it seems like the solution was pretty simple -- but without the Verizon tech being able to tell me what my particular router needed to make it work, I more or less had to stumble into it.
Mae Ploy Curry Paste Ingredients, Royal Dutch Shell Stock B, Mannion Nba Draft, Cambridge United Logo, Wild Pink Salmon, Watkins Toilet Bowl Cleaner, Maternity Allowance Ni, 1 M/s To Mph, Why Do I Pass Out After Drinking Alcohol, Mama Tom Yum Noodles Calories, I Love Bees, Jason Wade Lifehouse, How To Fix A Relationship In Trouble, Usp Isopropyl Alcohol Specification, List Of Mobile Network Operators In Indonesia, Curse Of The Vampire Coast, Draw 4 On Draw 4, Gas Königsforst Review, New Kid Read Online, How To Make A Duvet Cover From Sheets, Chair And Ottoman Sets Under $200, Versace Pour Homme 200ml, Gujarat Population By Religion, Cute Mango Wallpaper, Verragio Cubic Zirconia Engagement Rings, Meiji Milk Ingredients, No Samsung Portable Ssd Is Connected T7, Search And Rescue Certification, Cubic Feet To Cubic Inches, Effect Of Education On Employment, Viscosity Of Common Liquids, Lowest Crime Rate In The World 2020, Bob Bob Ricard Drinks Only, Ikea Flaxa Headboard With Storage Compartment,